Cowl heat sheild - Printable Version

Cowl heat sheild - Printable Version

+- Venice Forums (https://www.veniceforums.com)
+-- Forum: Techs, Mods, and Repairs (https://www.veniceforums.com/Forum-Techs-Mods-and-Repairs)
+--- Forum: Engine Mods (https://www.veniceforums.com/Forum-Engine-Mods)
+--- Thread: Cowl heat sheild (/Thread-Cowl-heat-sheild)

Cowl heat sheild - nusvul@yahoo.com - 07-24-2021

I have a 2021 Venice and the heat shield that is glued to the underside of the cowl keeps falling off. I was thinking of using spray glue to glue it back on again. It has glue on it but it has fallen off twice. Anybody else have this problem?

RE: Cowl heat sheild - Vector-BFC - 07-24-2021

(07-24-2021, 12:06 PM)nusvul@yahoo.com Wrote: I have a 2021 Venice and the heat shield that is glued to the underside of the cowl keeps falling off. I was thinking of using spray glue to glue it back on again. It has glue on it but it has fallen off twice. Anybody else have this problem?

Mine has detached 3 times. I used the strongest spray on glue available and it still comes off. Anyone know of a stronger glue?

RE: Cowl heat sheild - nusvul@yahoo.com - 08-03-2021

(07-24-2021, 04:39 PM)Vector-BFC Wrote:
(07-24-2021, 12:06 PM)nusvul@yahoo.com Wrote: I have a 2021 Venice and the heat shield that is glued to the underside of the cowl keeps falling off. I was thinking of using spray glue to glue it back on again. It has glue on it but it has fallen off twice. Anybody else have this problem?
Mine has detached 3 times. I used the strongest spray on glue available and it still comes off. Anyone know of a stronger glue?

So I tried a contact cement that is used to glue rubber pipe insulation toghter. It is super strong and flexible. It is called K-Flex 320 contact adhesive from Amazon and it is holding very well. First I removed the glue on the heat shield wearing gloves and using an acetone soaked rag. You you can buy acetone solvent in your local paint department. It is kind of a messy and smelly outside job. Do not get acetone anywhere near your Vanderhall it will disolve the paint and plastic instantly. Then I painted the heat shield and cowl with the glue and let it tack for a couple minutes. I used a cheap one in paint brush to apply the glue. Then I carefully rolled the heat shield on to the glue. Good luck.

RE: Cowl heat sheild - halvarez1017 - 08-27-2021

(08-03-2021, 12:46 AM)nusvul@yahoo.com Wrote:
(07-24-2021, 04:39 PM)Vector-BFC Wrote:
(07-24-2021, 12:06 PM)nusvul@yahoo.com Wrote: I have a 2021 Venice and the heat shield that is glued to the underside of the cowl keeps falling off. I was thinking of using spray glue to glue it back on again. It has glue on it but it has fallen off twice. Anybody else have this problem?
Mine has detached 3 times. I used the strongest spray on glue available and it still comes off. Anyone know of a stronger glue?
So I tried a contact cement that is used to glue rubber pipe insulation toghter. It is super strong and flexible. It is called K-Flex 320 contact adhesive from Amazon and it is holding very well. First I removed the glue on the heat shield wearing gloves and using an acetone soaked rag. You you can buy acetone solvent in your local paint department. It is kind of a messy and smelly outside job. Do not get acetone anywhere near your Vanderhall it will disolve the paint and plastic instantly. Then I painted the heat shield and cowl with the glue and let it tack for a couple minutes. I used a cheap one in paint brush to apply the glue. Then I carefully rolled the heat shield on to the glue. Good luck.

I used aluminum tape for heating it seems to work so far.

RE: Cowl heat sheild - RustyTeeth - 09-12-2022

Cut new piece of space pak. Double insulated and ran flexible metal duct tape. Amazon has Few thousand miles still holding. Used 3m ultra strong headliner spray glue after light scuff with sand paper so glue can grab, and alcohol cleaning. Made the entire hood more ridged and quiets everything down. Obviously not the blow off valve!
[attachment=301]

Here is what I used US Energy Products (3MM Reflective Foam Insulation Shield, Heat Shield, Thermal Insulation Shield Radiant Barrier 16" x10ft 12.5sqft (One Pack)
Brand: US Energy Products
[i]4.3 out of 5 stars[/i] 280 ratings
$16.88$16.88

One layer closed-cell foam bonded between two layers of highly reflective metalized aluminum polyester film. Industrialized strength, lightweight yet durable insulation designed to hold staples without tearing. Does not compress, collapse or disintegrate. Reflects 97% of radiant heat, emits less than 3% of heat, Class 1 / Class A fire rated radiant barrier that has passed the ASTM E84 test & ASTM E2599
Non-toxic, non-carcinogenic, fiber-free, safe to handle and does not require protective clothing or respirators to install. Easy to install and maintenance free, cuts easily with utility knife or scissors and installs easier than fiberglass. Simply staple, nail, glue or use a spray adhesive to hold in place! No mess, and no itchy fibers!
Not affected by moisture or humidity. Inhibits condensation and does not promote the growth of fungi, mold or mildew. Does not promote nesting of insects or rodents. Non-flammable, flame retardant
Saves energy by reducing the stress on heating and cooling systems, keeping your home warmer in the winter, and cooler in the summer. It can reduce utility bills substantially all year round. As well as provides benefits of soundproofing when used in walls, ceilings and floors. Can also increase your overall property value depending on use.
Made in USA / Class 1 Class A Fire Rated / Waterproof